Electric sump pump SP2000 with pipe and check valve

Sump Pump Model SP2000

Service Requirements:

	1/3 HP, 115 VAC, 60 HZ, Single Phase, 3400 RPM, 3.0 AMP
	Minimum circuit breaker: 10 AMP

Pumping Rates:

	2,000 GPH at 9 Foot Discharge Head
	2,500 GPH at 5 Foot Discharge Head
	Maximum head: to 30 feet
	Pumping range: 6 inches
	Minimum sump diameter: 12"

Go to Online Purchasing for pricing and information

Electric sump pump SP1300 with pipe and check valve

Sump Pump Model SP1300

Service Requirements:

	1/4 HP, 115 VAC, 60 HZ, Single Phase, 3400 RPM, 2.4 AMP
	Minimum circuit breaker: 10 AMP

Pumping Rates:

	1,300 GPH at 9 Foot Discharge Head
	1,800 GPH at 5 Foot Discharge Head
	Maximum head: to 23 feet
	Pumping range: 3 inches
	Minimum sump diameter: 9"

Go to Online Purchasing for pricing and information

See ordering information at the bottom of this page or click here.

Our primary sump pumps come in two sizes and both have a small footprint for use in any size sump. These are especially useful in smaller, confined, or congested sumps, but may be used in any size sump. You only need 12" diameter sump size to be able to fit either one of these pumps, and as small as 9" for the SP1300. So if you have a 5 gallon bucket being used as a sump, this will fit. They both come complete with float, check valve, a short section of PVC pipe, and a PVC male adapter to screw into the outlet fitting of the pump. This makes it easy to replace an existing sump pump or for a new installation.

Each sump pump model comes with:

1-1/2” PVC Pipe x 12” long.
Socket x male threaded adapter to screw into pump outlet.
Compression Fitting Check Valve, sized to fit 1-1/2” & 1-1/4” PVC pipe, using included rubber bushings.
Operates on 110V wall plug. GFCI Protected, dedicated outlet recommended (required in most areas).

Sump Pump Features:

Corrosion-resistant stainless steel motor casing, shaft, and fasteners.
Bearings: Upper and lower heavy duty ball bearing construction.
Motor permanently lubricated for extended service life and rated for continuous operation. All ratings are within the working limits of the motor.
Complete unit is light weight, portable and compact.
Power cord: 10 feet long, Heavy duty with 3-prong plug.
Built in thermal overload protection with automatic reset.
Float switch: SP 2000: Tether float switch, easily adjusted at time of installation.
Float switch: SP1300:Built-in non-mercury vertical type (low profile).
Agency listings: UL & CSA Approved.
One year warranty.

Pump Mounting Kit (PMK)

This is a simple, effective stainless steel sump pump mounting bracket that can be used to add a second electric sump pump ABOVE your main sump pump. In many cases, there is a need for higher pumping capacity, but not all the time. There are often just a few times during the year that higher pumping rates are needed, but most of the time, a smaller sump pump can do the job.

Need more pumping capacity, but not all the time?

Why operate a large capacity (3,000+ GPH) sump pump full time, when you may only need a standard capacity pump most of the time and a secondary pump at times of higher inflows?

Here's the perfect solution:

Place the SP2000 at the bottom of the sump to be your main pump.

Hang the SP1300 on our PMK Bracket above the SP2000.

The SP2000 handles the water just fine most of the time.

But...if a higher pumping rate is needed during the heavier inflows, the SP1300 kicks in when the SP2000 can't keep up, assisting the main pump and keeping the floor dry.

The Model SP2000 may also be mounted to the PMK Bracket just like the SP1300 to give you the ability to use a higher capacity pump as your auxiliary sump pump. When ordering the pump WITH the PMK, we will attach the pump to the pump bracket for you and ship it mostly assembled, to save you time. This means that the extra parts that come with the pump when ordered alone will be replaced with the parts from the PMK.

Go to Online Purchasing for pricing and information

Sump Pump Model SP1300 Mounted On Pump Mounting Bracket showing all the parts

You get everything you need to hook up an auxiliary sump pump when you get the PMK:

Stainless Steel Pump/Floor Bracket
(2) Hose Barb Adapters
(2) Hose Clamps
(4 Feet) Clear/Grey Hose
(1) PVC Threaded Elbow
(1) PVC Check Valve
(1) PVC Tee 1-1/2"
(2) PVC Bushings 1-1/2" x 1-1/4"
Hardware, Cable Ties, and Instructions

Below is the SP1300-PMK shown at the left as a drawing suspended above the existing main sump pump to illustrate how you can create an auxiliary sump pump system using our PMK (Pump Mounting Kit) to hang the pump over the side of the sump and easily make all your connections. The center photo shows the Model SP1300 attached to the Stainless Steel Bracket and the parts included to connect it to the main pump discharge pipe. The photo at the right is the SP1300 attached to the mounting bracket using a large Stainless Steel Hose Clamp that fits around the body of the pump and bolted to the back of the stainless steel plate. This plate is then attached to an "L" shaped Stainless Steel Bracket that holds the pump suspended above the other pump, as shown in the drawing to the left.

Sketch of SP1300 Mounted above SP2000 as auxiliary sump pump

Sump Pump Model SP1300 Mounted on PMK Bracket as though set in sump above primary sump pump

Sump Pump Model SP1300 Mounted on Stainless Steel Bracket

Drawing of the SP1300 in Pump Mounting Kit (PMK) unit suspended above the main sump pump.

Fully assembled SP1300 as it comes when ordering with the Pump Mounting Kit (PMK)

Sump Pump SP1300 in the pump mounting bracket that comes with the Pump Mounting Kit (PMK).

Go to Online Purchasing for pricing and information